SaturnFans.com
saturnfans.com - classifieds - forums - webmail


Go Back   SaturnFans.com Forums > Search Forums

Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: OldNuc
Forum: S-Series Tech 03-26-2014, 07:55 AM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

Lots of things are available at the FLAPS. When it comes to bearings that are very difficult to replace I tend to go to a quality bearing suppler and go with the high quality - high dollar bearing.
Forum: S-Series Tech 03-09-2014, 12:17 AM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

It is too thick and you have clearance problems, just like you will have if you use RTV on the 5th gear cover. Get the correct gasket or make one out of a grocery bag and very thinly coat both sides...
Forum: S-Series Tech 03-08-2014, 09:49 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

Is that 6ml?, should be. Probably enough as it is thin and watery and the bead only has to be 1 to 3 mm wide and 1mm is plenty.

1 mm = 0.039" or 1/25th inch
Forum: S-Series Tech 03-08-2014, 02:54 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

You lay down a continuous thin thread all the way around that flange, circle the 5 bolt holes around the differential and inside of all other bolt holes. Center the bead 1-3mm wide on the mating...
Forum: S-Series Tech 03-04-2014, 12:52 AM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

The NAPA website is useless as it only understands NAPA part numbers.
Forum: S-Series Tech 03-04-2014, 12:37 AM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

This is what you are looking for to seal the case. http://www.mcmaster.com/#loctite-515/=qxwrpk The 515 is a good number

This is from the Locktite site, it is under industrial....
Forum: S-Series Tech 02-03-2014, 02:54 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

They look like a plain snap ring with one end bent inward very slightly. These will work. Buy them so they will fit tightly in the bearing recess and then if too thick sand to fit. You can use the...
Forum: S-Series Tech 02-02-2014, 01:34 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

You can make them out of snap rings, the actual shim is probably not available unless you buy a trans rebuild kit that contains those parts. Bearings are held to very tight tolerances so as long as...
Forum: S-Series Tech 01-31-2014, 08:44 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

Both are the same number and there is a ring in the transmission now. The case is sealed with a special locktite(#515) and if you are ,real lucky the existing ring will be fine. Do not use RTV to try...
Forum: S-Series Tech 01-31-2014, 12:21 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

When digging into a transmission it is a very good idea to have either the FSM in front of you or a subscription to ALLData. There are many critical settings that are not obvious without these...
Forum: S-Series Tech 01-31-2014, 02:28 AM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

Oh, yes there are, on the left side against the outer race of the carrier bearing there is what looks like a snap ring, that is a shim and they come in sizes or you buy sand paper and make them. ;)
Forum: S-Series Tech 01-30-2014, 07:19 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

Pull the bearings out and get the complete bearing number from the actual bearing. 21003317 is OEM number but I would go bearing shopping once I had the actual number as I suspect you can buy a much...
Forum: S-Series Tech 01-30-2014, 09:57 AM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

The rod falls out as nothing is holding it in. Tie up the clutch pedal now or you will have problems later. The slave piston is held in the cylinder with a wire ring and if the piston comes out then...
Forum: S-Series Tech 01-30-2014, 08:27 AM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

A stage 3 is going to be a bit harsh and a potential PITA in traffic. IIRC I bought this kit on a best offer of 200:...
Forum: S-Series Tech 01-29-2014, 11:44 PM
Replies: 70
Views: 6,550
Posted By OldNuc
Re: Questions about Partial Rebuild

I am quite happy with my stage 2 clutch, does not slip and does not grab either.
Showing results 1 to 15 of 15

 
Forum Jump

All times are GMT -4. The time now is 07:12 AM.

Advanced Forum Search | Advanced Photo Search


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
SaturnFans.com. The Saturn Enthusiasts Site.