SaturnFans.com
saturnfans.com - classifieds - forums - webmail


Go Back   SaturnFans.com Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.10 seconds.
Search: Posts Made By: spacetrace33
Forum: S-Series Tech 07-21-2020, 04:34 PM
Replies: 8
Views: 653
Posted By spacetrace33
Re: Weird electrical issues 2000 SL

It says for splice pack #2, H brace ground.[/QUOTE]

Letter R in above diagram.
Forum: S-Series Tech 07-21-2020, 04:17 PM
Replies: 8
Views: 653
Posted By spacetrace33
Re: Weird electrical issues 2000 SL

According to the fsm, the I/P cluster grounds are on A6 and B4, both black wires

Ip splice ground pack #2..... goes through B1 on blue BCM connector as well.

It says for splice pack #2, H brace...
Forum: S-Series General 07-18-2020, 10:14 PM
Replies: 91
Views: 6,465
Posted By spacetrace33
Re: RIP Oldnuc

Old Nuc...he was a really smart guy and always willing to help others.

The saturn community lost a great guy.
Forum: S-Series Tech 07-09-2020, 05:22 AM
Replies: 4
Views: 431
Posted By spacetrace33
Re: Brakes go all the way down.

Usually when the booster goes, the brake pedal gets stiff. Like braking with the engine off.
Forum: S-Series Tech 12-25-2019, 02:38 AM
Replies: 6
Views: 252
Posted By spacetrace33
Re: O2 slow response only with AC on.

The code being set is P0133. Before the cat.

The weather here in iowa is cold as well lol. I like to run AC every now and then to try and clear any moisture inside the car.
Forum: S-Series Tech 12-22-2019, 03:48 PM
Replies: 6
Views: 252
Posted By spacetrace33
O2 slow response only with AC on.

Title says it all...o2 slow response. Only seems to happen with the AC on and pulling hard.

Replaced with NGK, twice. Seemed to work for a couple months w/o code.

Anybody have insight as to...
Forum: S-Series Tech 10-16-2019, 03:09 PM
Replies: 4
Views: 324
Posted By spacetrace33
Re: Rear main seal

OldNuc nailed this once again!

VC gasket was installed last year, per fsm instructions.

Only putting a dab of rtv at the tcc joints and using a felpro gasket set.

Guess it's time to take...
Forum: S-Series Tech 08-25-2019, 11:50 AM
Replies: 4
Views: 324
Posted By spacetrace33
Rear main seal

Let me give you some background.

Rebuilt this 99 engine a year ago, using the fsm as a guide. It developed an oil leak early on. Suspicions were high that it was the rear main.

Instead of...
Forum: S-Series Tech 09-11-2018, 04:04 PM
Replies: 12
Views: 520
Posted By spacetrace33
Re: Lopey idle with ac running

What causes the clutch to kick in and out?
Forum: S-Series Tech 09-11-2018, 03:58 PM
Replies: 12
Views: 520
Posted By spacetrace33
Re: Lopey idle with ac running

Nice. Thanks for great leads.

I know almost nothing when it comes to A.C. systems.

With what uluz says, it sounds like the ac clutch should stay engaged during idle....no on and off rapid...
Forum: S-Series Tech 09-10-2018, 10:28 PM
Replies: 12
Views: 520
Posted By spacetrace33
Re: Lopey idle with ac running

Exactly


I should add that once i start going again, say light turns green and its still acting up at idle...once the wheels get moving again(in gear), it "seems" fine.
Forum: S-Series Tech 09-10-2018, 10:17 PM
Replies: 12
Views: 520
Posted By spacetrace33
Re: Lopey idle with ac running

Fdryer

200? To 900 rpms repeatedly means:

In neutral, the idle bounces back and forth between 200ish and 900, several times.

Sometimes the idle will find itself....othertimes its jumping...
Forum: S-Series Tech 09-10-2018, 08:09 PM
Replies: 12
Views: 520
Posted By spacetrace33
Lopey idle with ac running

Havent posted on here for a while so here it goes the scenario.

Start car, turn ac on, blows cold (constantly), idle is perfect. Start driving-which seems normal. Put in neutral for a stop and...
Forum: S-Series Tech 06-06-2018, 09:17 PM
Replies: 12
Views: 508
Posted By spacetrace33
Re: O2 sensor woes.

Fdryer, wow! I had to reread that a couple of times.

Ok, so I put the sohc PCM in and ran it long enough to see that there's still a cl-fault. (Ran bad, in case anybody is wondering). Put dohc...
Forum: S-Series Tech 06-06-2018, 12:04 AM
Replies: 12
Views: 508
Posted By spacetrace33
Re: O2 sensor woes.

Close.... If I decide to yank and run 3g dohc wiring....I'll be upsetting the map sensor wiring/connection. If I get to that bridge, I'll cross it then.

Ok, so sohc PCM is on the agenda. What's...
Forum: S-Series Tech 06-05-2018, 10:59 PM
Replies: 12
Views: 508
Posted By spacetrace33
Re: O2 sensor woes.

The 99 had zero error codes in the 99 body.
The 2000 had zero error codes with the sohc.
The error code didn't pop up right away after swapping things.

This Frankenstein is fresh meat. 30...
Forum: S-Series Tech 06-05-2018, 10:07 PM
Replies: 12
Views: 508
Posted By spacetrace33
Re: O2 sensor woes.

I need to verify the most major concern...

Will not go into closed loop. Scan tool reads cl error.
Forum: S-Series Tech 06-05-2018, 10:03 PM
Replies: 12
Views: 508
Posted By spacetrace33
Re: O2 sensor woes.

Ah, yes, my apologies fdryer.

I have 2000 sohc wiring harness with 2000 dohc PCM.
Forum: S-Series Tech 06-05-2018, 08:52 PM
Replies: 12
Views: 508
Posted By spacetrace33
Re: O2 sensor woes.

Running 2g map sensor on 3g dohc PCM....I may need more info about this.
Forum: S-Series Tech 06-05-2018, 02:33 PM
Replies: 12
Views: 508
Posted By spacetrace33
O2 sensor woes.

Idk where to begin, so I'll start with p0038, heater circuit high. I changed the rear O2 bc the threads stripped on original sensor.

Replaced it with an o'reillys Bosch direct fit-for the 2000,...
Forum: S-Series Tech 02-01-2018, 05:28 PM
Replies: 129
Views: 4,928
Posted By spacetrace33
Re: Starting to get into all the small details

Ok. So just updating since it's been a while. Got the bottom end done. I did plasigauge every bearing. While the numbers are written in the garage, and I'm not there, they were on the high side, but...
Forum: S-Series Tech 10-23-2017, 08:44 PM
Replies: 129
Views: 4,928
Posted By spacetrace33
Re: Starting to get into all the small details

Haha Bill. Don't apologize. Thanks for looking out.
Forum: S-Series Tech 10-23-2017, 04:03 PM
Replies: 129
Views: 4,928
Posted By spacetrace33
Re: Starting to get into all the small details

Whoa. Let's go back a chapter and get on same page. 😂

Short version of story is

I'm going to be using the heavy crank with .50mm undersize bearings.

I was bummed they didn't wanna...
Forum: S-Series Tech 10-23-2017, 09:52 AM
Replies: 129
Views: 4,928
Posted By spacetrace33
Re: Starting to get into all the small details

Waiex I'm so grateful you brought that topic up.

Called m s today to let him know I'm sending Pistons over. I kinda felt bad asking him if he knows what a plateau finish is. He said he did and...
Forum: S-Series Tech 10-21-2017, 01:46 AM
Replies: 129
Views: 4,928
Posted By spacetrace33
Re: Starting to get into all the small details

Just to update, got the Pistons today.

Will bring them to m s Monday. Hope to get answers on that crankshaft.

A few more parts came in, gaskets (most didn't survive, they were the RA...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -4. The time now is 04:36 AM.

Advanced Forum Search | Advanced Photo Search


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
SaturnFans.com. The Saturn Enthusiasts Site.