SaturnFans.com
what's new (beta) - classifieds - forums - photos


Go Back   SaturnFans.com Forums > Models > Saturn Vue > Vue Tech
Register FAQ Members List Groups Calendar Chat Room Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 07-30-2010, 03:39 AM   #1
knclark67
Junior Member
knclark67 is on a distinguished road
 
Join Date: Apr 2008
Posts: 20
Default Vue stopped working. Blinking security light.

I have a 2003 Saturn Vue 6 cylinder automatic. I was driving and my car just turned off and did not start again. The starter would begin but the car would not crank. I disconnected the battery and then reconnected the battery and tried to turn it on, the car popped and a burning smell followed. I did this twice. When I went out later I noticed the security light was blinking. Based on some research it may be the body control module.
Is it this part? If so how do I go about replacing it or whatever part it may be? If this can only be done by a dealer where can I find one now?

REWARD EXCELLENCE!

Add to knclark67's Reputation
Rate the quality of this post and help knclark67 reputation points. Click the reputation button near the bottom left corner of this message box. Thank you!
knclark67 is offline   Reply With Quote
SaturnFans.com Sponsored Links
Old 07-30-2010, 06:09 AM   #2
fdryer
Super Member
fdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond repute
 
fdryer's Avatar
 
Join Date: Jan 2006
Location: NYC
Posts: 42,908
 

2003 L-Series 3.0L Sedan
Default Re: Vue stopped working. Blinking security light.

The engine turning off and not able to start again may be the crank position sensor (CPS), next to the oil filter. The starter working but the engine never firing up is usually a tell tale indication of a failed cps. Removing and measuring it for resistance should read between 700-1200 ohms otherwise an open reading means failure, replace it. Check on this part before continuing on otherwise you may wear out the battery trying multiple starting attempts.

The security light flashing can be reset in one of two ways; leave the ignition in the ON position beyond 10-minutes until it stops flashing then turn off the ignition before trying another start or perform the 30-minute relearn routine posted on these forums. You can seach for the procedure.

Before starting up, have the battery fully charged in case it was drained from starting attempts.

The bcm has many functions including the Passlock theft deterrent system but may not be the problem, yet. If the reset procedure works the bcm is working correctly.

REWARD EXCELLENCE!

Add to fdryer's Reputation
Rate the quality of this post and help fdryer reputation points. Click the reputation button near the bottom left corner of this message box. Thank you!
fdryer is online now   Reply With Quote
Old 07-30-2010, 09:05 PM   #3
knclark67
Junior Member
knclark67 is on a distinguished road
 
Join Date: Apr 2008
Posts: 20
Default Re: Vue stopped working. Blinking security light.

Thank you very much. I will look into this part. If you could provide me some insight into the procedure for removing this part I would greatly appreciated.

REWARD EXCELLENCE!

Add to knclark67's Reputation
Rate the quality of this post and help knclark67 reputation points. Click the reputation button near the bottom left corner of this message box. Thank you!
knclark67 is offline   Reply With Quote
Old 07-30-2010, 10:34 PM   #4
fdryer
Super Member
fdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond repute
 
fdryer's Avatar
 
Join Date: Jan 2006
Location: NYC
Posts: 42,908
 

2003 L-Series 3.0L Sedan
Default Re: Vue stopped working. Blinking security light.

CPS removal is straight forward but does require a Torx socket. I don't know the size.
Attached Images
File Type: gif Vue cps.gif (34.3 KB, 18 views)

REWARD EXCELLENCE!

Add to fdryer's Reputation
Rate the quality of this post and help fdryer reputation points. Click the reputation button near the bottom left corner of this message box. Thank you!
fdryer is online now   Reply With Quote
Old 08-01-2010, 12:27 AM   #5
knclark67
Junior Member
knclark67 is on a distinguished road
 
Join Date: Apr 2008
Posts: 20
Default Re: Vue stopped working. Blinking security light.

Removed the part, it was Torx size E8. Had it tested. It tested at 910 ohms. Tried starting car again, but there is a loud pop and a burning smell. I am open to suggestions for the next step or alternatives. Thank you very much for your help.

REWARD EXCELLENCE!

Add to knclark67's Reputation
Rate the quality of this post and help knclark67 reputation points. Click the reputation button near the bottom left corner of this message box. Thank you!
knclark67 is offline   Reply With Quote
Old 08-01-2010, 12:39 AM   #6
fdryer
Super Member
fdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond reputefdryer has a reputation beyond repute
 
fdryer's Avatar
 
Join Date: Jan 2006
Location: NYC
Posts: 42,908
 

2003 L-Series 3.0L Sedan
Default Re: Vue stopped working. Blinking security light.

And still no SES light? Next step can be fuel pressure testing. When the igition key is turned ON there will be a faint hum/hiss of the fuel pump running (try listening for it) for 2-3 seconds then shutting off (for safety); locate the fuel rail's test valve, remove the large black plastic cap (this schrader valve resembles a tire valve), cover the valve loosely with a rag while depressing the valve stem expecting a healthy spray of fuel. No fuel or a dribble means a fuel issue; fuse, pump relay, wiring, ground.

REWARD EXCELLENCE!

Add to fdryer's Reputation
Rate the quality of this post and help fdryer reputation points. Click the reputation button near the bottom left corner of this message box. Thank you!
fdryer is online now   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
blinking security lite after new ECM montemontana L-Series Tech 1 12-07-2009 01:05 PM
Security light blinking constantly when locked? 02Saturnlady S-Series Tech 9 06-28-2009 02:04 PM
speakers stopped working after fixing brake light madcomic2000 L-Series General 1 11-21-2008 11:31 PM
Vue wont start Security light blinking Powellak Vue Tech 2 01-16-2007 12:02 AM
Security Light non-stop blinking RustyJCNC L-Series General 5 08-25-2004 01:53 PM


All times are GMT -4. The time now is 06:14 PM.

Advanced Forum Search | Advanced Photo Search


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
SaturnFans.com. The Saturn Enthusiasts Site.